Sikkens Proluxe UV Interior Clear 1 Gallon Pail

Sikkens Proluxe UV Interior Clear Wood Finish

Sikkens ProLuxe Cetol  UV Interior is a unique waterborne product designed to protect light colored interior wood, yet leave no color or sheen on the surface. UV absorbers minimize yellowing for a natural look.

FacebooktwitterpinterestmailFacebooktwitterpinterestmail
Clear
SKU: S-UV. Category: . Tag: .

Product Description

FacebooktwitterpinterestmailFacebooktwitterpinterestmail

Sikkens Mail in Rebate Offer

Same Sikkens formula….a new name!

 Sikkens UV Interior Clear Wood Finish is a unique waterborne product designed to protect interior wood yet leave no color or sheen on the surface. When a beautiful, natural appearance is desired, use Sikkens UV Interior Clear Wood Finish (recommended for use on light colored woods only).

Product Type: Oil-based formula

Uses:  Most types of interior wood, logs, paneling, sunrooms, and ceilings

NoteNot for use on kitchen cabinets, floors and high-humidity areas

  • Allows a natural uncoated matte look to the wood
  • No color
  • No sheen
  • For use on bare, light colored wood
  • Short dry time between coats
  • Translucent
  • Water based Acrylic Resin
  • UV absorbers minimize yellowing for a natural look.
  • Not manufactured with lead or mercury containing materials
  • Easy clean-up and low odor

Product Facts

Coverage
  • Apply at 400-500 sq ft/gallon
  • Actual coverage may vary depending on the type, age and texture of the wood and application method.
  • Available in 1 gallon and 5 gallon containers

 

Shelf Life
  • 2 years maximum – unopened
  • Freezable
Application Temperature
  • Apply between 50° F (10° C) – 95° F (35° C).

 

Application Methods
  • Premium quality nylon-polyester brush
Frequency
  • The longevity of the coat depends on the amount of daily wear and exposure to ultraviolet light.
  • Clean and prepare surface under GENERAL SURFACE  PREPARATION reducing the cleaning solution to two (2) ounces of 100% powdered Tri-Sodium Phosphate (TSP) or phosphate-free substitute.
  • Apply one or two coats depending on the extent of the wear.

 

Special Instructions
  • Clean new or untreated interior wood with a solution of four (4) ounces of 100% powdered Tri-Sodium Phosphate (TSP) or phosphate-free substitute in one gallon of warm water.
  • Do not apply Cetol UV Interior Wood Finish over stain; use on bare, light colored wood only.
  • Remove hardware. Any hardware that cannot be removed should be covered with painters tape
  • Initial sanding for bare wood.
  • Fill any nail holes or cracks with a good quality acrylic wood filler such as Energy Seal matching the color of the wood.
  • Do not use oil-based fillers, putties or wax sticks
  • Requires two coats and sanding between applications

 

Drying Time At 77°F (25°C) & 50% RH:

  • Dries to touch in one hour
  • Recoat in two to four hours

 

 

Surface Preparation

General surface preparation for New or Unfinished Wood

 All wood surfaces must be thoroughly clean, dry and free of dirt, grease, grime, mildew, mill glaze and previous coatings before applying Sikkens ProLuxe Cetol UV Interior Wood Finish. Clean surface with a solution of four (4) ounces of 100% powdered Tri-Sodium Phosphate (TSP) or Phosphate-free substitute in one gallon warm water.

  1. Remove hardware. Any hardware that cannot be removed should be covered with painters tape.
  2. Clean surface with a solution of four (4) ounces of 100% powdered Tri-Sodium Phosphate (TSP) or phosphate-free substitute in one gallon of warm water.
  3. Wipe surface with a damp cloth or sponge and clear water to remove any residue and allow to dry. Do not allow solution to dry on the wood surface.
  4. Fill any nail holes or cracks with a good quality acrylic wood filler such as Energy Seal matching the color of the wood. Do not use oil-based fillers, putties or wax sticks. Allow to dry completely before sanding.
  5. Sand the surface with 150-180 grit sand paper. Always sand with the grain for a smoother surface and no sanding marks. Remove sanding dust with vacuum, then wipe surface with a damp cloth to remove any remaining particle. For a smoother final finish sand surface again with 180-220 grit sandpaper and wipe clean.

 

Exotic Hardwood

  1. 1. Ipe, mahogany, iron wood, tiger wood and teak woods exhibit a dense cell structure which may reduce the ability of a coating to penetrate the wood surface.
  2. Clean and prepare all wood surfaces as specified under general surface preparation.
  3. Immediately prior to applying coating, wipe surface with acetone.

 

Previously Coated Wood

  1. Previous stains, varnishes or sealers must be completely and thoroughly removed prior to application of Cetol UV Interior Wood Finish.
  2. After removal of previous coatings, clean and prepare surface as specified under general surface preparation.

WARNING! If you scrape, sand, or remove old paint, you may release lead dustUse Lead Out Lead Paint Remover. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear an NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

Application

CAUTION: Do not apply Cetol UV Interior Wood Finish over stain; use on bare, light colored wood only.

  1. Stir before and periodically during application.
  2. Do not thin.
  3. Apply between 50° F (10° C) 95° F (35° C).
  4. Do not apply in direct sunlight, may cause uneven color because of shortened open time and poor penetration.
  5. Apply Cetol UV Interior Wood Finish in the direction of the wood grain using a premium quality nylon-polyester brush. Two coats recommend for optimal performance.
  6. Allow first coat to dry four to six hours.
  7. Lightly sand with 220 grit sandpaper or a fine scuffing pad and remove sanding dusting with a dry cloth.
  8. Apply a second coat of Cetol UV Interior Wood Finish. A third coat may be applied to high wear areas after second coat has dried for four to six hours.

 

DRY TIME @ 77°F (25°C) & 50% RH:

  1. Dries to touch in one hour and to recoat in two to four hours.
  2. Low temperature, high humidity, thick films or poor ventilation will increase these times.
  3. Avoid heavy abrasions immediately following application.

 

Clean Up

Clean tools immediately with warm, soapy water. Clean spills right away with a damp cloth.

 

Safety Precautions

  • Danger! Harmful if inhaled.
  • Use only with adequate ventilation.
  • May cause central nervous system effects, including dizziness, headache or nausea.
  • Causes eye, skin and respiratory tract irritation.
  • Harmful if swallowed.
  • Overexposure may cause liver, kidney damage.
  • Keep out of the reach of children.
  • Notice: this product contains solvents.

 

Shipping Restrictions

Sikkens ProLuxe Cetol  UV Interior is available for shipment by ground only and is shipped via FedEx to the continental USA; with the exception of the following areas that are not approved for Sikkens Proluxe Cetol UV Interior use due to VOC regulations:

Please Note: Sikkens ProLuxe Cetol UV Interior cannot be sold to:

  • Canada
  • Counties in the South Coast Air Quality Management District of California which includes Orange, Los Angeles, Riverside and San Bernardino Air Quality Management District of California
  • Bay Area Air Quality Management District of California
  • San Joaquin Air Quality Management District of California
  • Ventura Air Quality Management District of California
  • Kern Air Quality Management District of California
  • Imperial Air Quality Management Districts of California

Please Note:  South Coast Air Quality Management District of California has an exemption for locations registered above 4,000 feet.

Please click here to determine if your address is included in this exemption.  To find out which California Air Quality District you are in click here.

 

 

 


MSDSClick here for this product’s MSDS

 

FacebooktwitterpinterestmailFacebooktwitterpinterestmail

Reviews

There are no reviews yet.

Be the first to review “Sikkens Proluxe UV Interior Clear Wood Finish”