See Soy Gel in Action!

 

 

 

WHAT IS SOY•GEL™ PROFESSIONAL PAINT STRIPPER?

SOY•Gel™ is an industrial strength, consumer friendly, paint, varnish and urethane remover. The product is made with 100% American grown soybeans. The low evaporation rate of SOY•Gel™ makes it possible to remove several layers of paint in one application. SOY•Gel™ contains no methylene chloride and is not an alkaline based stripper. The product cleans up easily with water and is safe to use according to the manufacturers directions. Unlike more traditional paint strippers SOY•Gel™ lets you work without the odor and can be safely used inside or outside.

WHAT MATERIALS CAN SOY•GEL™ BE USED ON?

SOY•Gel™ is safe to use on wood, brick, stone, metal,plaster and concrete.SOY•Gel™ should not be used on plastic, PVC, rubber, or drywall. When used outdoors protect plants and vegetation with a plastic drop cloth. SOY•Gel™ may be used on vertical as well as horizontal surfaces.

WHAT TYPES OF COATINGS WILL SOY•GEL™ REMOVE?

SOY•Gel™ has proven to remove most coatings including paints, stains, enamels, latex finishes varnishes, urethanes, epoxies as well as solvent and water based concrete sealers.

WILL SOY•GEL™ REMOVE MULTIPLE COATINGS?

Yes! SOY•Gel™has been proven to remove upwards of 20+ coatings in one application. The number of coatings that can be removed in one application depends on the thickness of the SOY•Gel™ which is applied and the amount of time it is allowed to work on the surface.

CAN SOY•GEL™ BE USED TO REMOVE LEAD BASED PAINTS?

Yes. During the removal of lead based paint , the lead paint residue becomes encapsulated in the gel, preventing airborne lead particles, and allowing for safe disposal.

CAN SOY•GEL™ BE USED TO STRIP LOG HOMES?

Yes! SOY•Gel™ is well suited to remove finishes from log homes such as urethane based finishes including Sikkens Cetol products as well as acrylic latex products such as Lifeline Exterior, Pro Guard, Lifeline Ultra-2, and Lifeline Advance.

HOW DO YOU APPLY SOY•GEL™?

For small jobs you can apply SOY•Gel™ with an inexpensive paint brush and glob it on to the surface . Be careful not to apply too thin a coat. Apply a 1/16th to 1/8th inch layer of SOY•Gel™ to the coating which is to be removed. For larger applications you can apply SOY•Gel™ with a straw broom or use a piston pump airless sprayer with a 519 tip. Allow the stripper time to work. Check the progress of the stripping action by using a scraper to see if the coating is softened down to the surface. If not, wait longer and recheck. SOY•Gel™ will remain wet and working for several hours. Longer is better. Let the stripper do its work. Once the coating is softened remove it with a scraper, industrial wet vacuum or other stripping tool. Reapply SOY•Gel™ when necessary to remove extra heavy coatings and repeat the steps above. After scraping off the final stripping residue, clean the surface by rinsing with water using a scrub brush or a power washer.

HOW LONG DO I LET SOY•GEL™ SIT BEFORE REMOVING?

Test scrape the surface every 10-30 minutes to see if the coating has lifted. Simple coatings like latex and urethanes take, on average, between 10-60 minutes. Epoxies and multiple layers of other coatings can take a few hours to overnight to lift. If applying outside, it is usually a good idea to cover with a thin mil plastic drop cloth to keep the SOY•Gel™ from drying out over an extended period of time.

WILL SOY•GEL™ RAISE THE GRAIN OF WOOD?

SOY•Gel™ it self will not raise the grain of wood. During final cleanup using too much water may raise the grain of the wood.

THESE ARE THE KIND OF RESULTS YOU CAN EXPECT WITH SOY•GEL™.

WHAT COVERAGE CAN I EXPECT WITH SOY•GEL™?

SOY•Gel™ will deliver coverage of 200 SF per gallon on horizontal surfaces and 130 SF per gallon on vertical surfaces.