WHAT IS THE X-100 NATURAL SEAL DECK
FINISH SYSTEM?
The
X-100 Natural Seal Deck
Finish System is a unique
oil borne deck finish
designed to protect your
deck from the environmental
forces of wind, rain,
snow, ice and sun.
X-100 Deck Finish protects
decking against cracking,
splitting, cupping, curling,
sapstain, mold and mildew.
The product replaces the
natural oils in the wood
fiber that were lost when
the tree was cut. X-100 Deck
Finish is recommended for
use on all new and seasoned
decking. The product uses
microfine color oxide
technology for deeper color
penetration. X-100 New Deck
Finish penetrates deep to
allow its UV inhibitors and
waterproofers to properly
protect your deck. The X-100
Deck Finish System is a two
coat application with a
PreFinish followed by a
final coat of X-100 New Deck
Finish.
WHAT ARE
THE ADVANTAGES OF USING X
-100 NATURAL SEAL NEW DECK
FINISH?
- Deeper product
penetration
- Faster dry time even on
new pressure treated
lumber
- Greater and deeper oxide
penetration for
long-term color fastness
- Eliminates need to
remove mill glaze
- Available in
ultra-transparent stains
that allow natural wood
grain to show through
- Formulated for minimal
evaporation to assure
maximum product
penetration and deck
protection
- Five year deck
protection
|
 |
HOW MUCH
AREA WILL X-100 DECK FINISH
COVER?
On new pressure treated
decking a gallon of X-100
New Deck Finish will cover
300 square feet. On old,
seasoned, or weathered
decking a gallon of X-100
New Deck Finish will cover
200 SF depending on the
porosity of the surface. For
best results the X-100 Deck
Finish System should be
applied to dry wood. Do not
apply if rain is forecast
during the next 36 hours.
WHAT COLORS ARE X-100 NEW
DECK FINISH AVAILABLE IN?
|
Cedar Tone
Gold |
Cedar Tone
Brown |
HOW DO
YOU APPLY X-100 NEW DECK
FINISH?
-
Apply
X-100 Pre Finish and New
Deck Finish with a
brush, long handled
staining pad or a low
pressure sprayer. Work
the product vigorously
into the decking. Do not
allow New Deck Finish to
puddle. Do NOT apply
this product with a
roller!!
- Apply as much X-100 Deck
Finish as the wood will
absorb to reach a
uniform appearance.
Please note that the
same piece of wood will
absorb differently in
certain areas.
- Keep a wet edge to avoid
lap marks.
- After X-100 Pre
Finish has flash dried
for 30 minutes or more
apply a second coat of
X-100 New Deck Finish to
complete your
application.
- X-100 requires a minumum
of 48 hours to dry. Each
horizontal surface may
have different drying
times due to variations
in porosity.
- The X-100 Deck Finish
System is designed for
Exterior Use Only! Do
Not use this product on
the Interior of
your home.
- Use mineral spirits or
dish detergent to clean
brushes and pads used to
apply X-100 Deck Finish.
If X-100 Deck Finish
should get on surfaces
such as glass, paint,
metal, caulking or
rubber remove
immediately with dish
detergent. If a spill is
dry remove with mineral
spirits.
WHAT IS THE
BEST WAY TO MAINTAIN A DECK
TREATED WITH THE X-100 DECK
FINISH SYSTEM?
Atmospheric
pollutants and ordinary
abrasive foot traffic will
leave dirt on deck surfaces.
Rainwater alone does not
wash such deposits away.
After a consistent rain,
squeegee the deck surface. (
Note: On stubborn dirt areas
use a mild dish detergent
and water solution with a
mild brushing action to
remove dirt, then rinse
with water.)
In the spring and the fall
wash your deck with X-180
Weathered Wood Restorer. In
high traffic areas an annual
maintenance coat of X-100
New Deck Finish is
recommended to maintain best
appearance and maximum
protection.
ARE X-100
NEW DECK FINISH COLOR
SAMPLES AVAILABLE?
Yes! Our sample kit contain
one ounce jars of Cedar Tone
Gold and Cedar Tone Brown is
available upon request. You
can request an X-100 Deck
Finish Sample Kit over
the Internet by filling
out a sample request form.
